Elna 792D
Payments starting from $10.00 per week. learn more
Explore the Elna 792D: 3 and 4-thread overlocking, rolled hems and differential feed. See included tools, threading advice and sewing FAQs.
$399.00 $599.00
Elna 792D: trim, sew and finish fabric edges
The Elna 792D brings three- and four-thread overlocking to garment sewing and everyday projects. It trims the fabric edge and encloses it with stitching in one pass. Use four threads for seams or three threads for lighter edge finishes, rolled hems and flatlocking. Narrow hemming, picot edging and gathering add more finishing options.
Adjustable differential feed helps you control wavy knit edges and puckering on fine woven fabrics. Manual controls let you adjust the stitch length, cutting width, thread tension and presser-foot pressure for your fabric.
Choose your seam finish
Four-thread overlocking joins and finishes fabric edges. Three-thread overlocking tidies raw edges, while flatlocking adds a decorative seam finish. Gathering gives you another option for creative projects.
For a three-thread rolled hem, slide the needle-plate setting knob to the rolled-hem position and follow the manual’s stitch settings. The needle plate stays in place during the changeover.
Adjust the fabric feed
Differential feed changes the relative movement of the front and rear feed dogs. Adjust it to help a knit edge lie flat or reduce puckering on lightweight woven fabric. You can also use it for gathering.
Set stitch length from 1 to 4 mm and cutting width from 3.1 to 7.3 mm. Adjustable presser-foot pressure gives you another way to fine-tune feeding. Test the settings on an offcut of your project fabric.
Follow the threading guides
Colour-coded thread paths and the threading chart guide you through setup. The large and small screwdrivers and tweezers are included for threading and needle changes. The telescopic thread antenna guides thread from the four-spool stand.
The tension dials are manual. Follow the threading instructions for the stitch you want to use and test the tension on a matching offcut. This model uses manual threading and HAx1SP ballpoint needles.
Work at your own pace
The electronic foot control operates the machine at speeds up to 1,300 stitches per minute. Retract the upper knife when your technique calls for sewing without trimming the edge. The manual cutter on the face plate trims the thread chain after sewing.
The 8 kg machine has a carry handle. It comes fully threaded. Make a test seam before starting your project so you can check the finish on your own fabric.
Included accessories
- Standard presser foot fitted to the machine
- Pack of HAx1SP ballpoint needles
- Large screwdriver
- Small screwdriver
- Tweezers
- Electronic foot control
- Instruction book
A machine cover is not included in the standard package. Optional feet and attachments are available for techniques such as piping, gathering and beading. Ask our team to help you choose the right attachment.
Key specifications
- Threads
- Three or four
- Stitch options
- Overlocking, rolled hemming, flatlocking and gathering
- Maximum sewing speed
- 1,300 stitches per minute
- Stitch length
- 1–4 mm
- Cutting width
- 3.1–7.3 mm
- Differential feed ratio
- 0.5–2.25
- Thread tension
- Manual dials
- Presser-foot pressure
- Adjustable
- Upper knife
- Retractable
- Needle system
- HAx1SP ballpoint
- Machine weight
- 8 kg
- Thread cutting
- Manual cutter on the face plate
- Free arm
- No
- Two-thread converter
- No
- Coverstitch and chain stitch
- No
Frequently asked questions
Is the Elna 792D suitable for a first overlocker?
Its colour-coded paths, threading chart and manual controls give you clear guidance while learning. Practise threading and adjusting the finish on scraps before starting a garment. Our friendly team can help you decide whether its features suit your sewing.
How do I thread the 792D?
Switch the machine off and follow the threading order and colour-coded diagram in the supplied instruction book. Check that each thread follows its full route and sits in the tension discs. Use the manual settings as your starting point, then test on matching fabric.
Can it make a rolled hem?
Yes. It makes a three-thread rolled hem. Move the needle-plate setting knob to the rolled-hem position and use the needle and tension settings in the manual. You do not need to replace the needle plate.
What does differential feed do?
It adjusts how the front and rear feed dogs move fabric through the machine. This helps control stretched knit edges and puckered woven fabric. Test on the same fabric as your project and adjust until the edge lies as you want it.
Can it replace my sewing machine or make a coverstitch hem?
It works alongside a sewing machine by trimming and finishing edges. It does not make coverstitch hems, chain stitches or conventional sewing-machine buttonholes. Use a sewing machine for tasks such as zips and buttonholes.
Can I use two threads or sew without trimming?
The 792D uses three or four threads and has no two-thread converter. You can retract the upper knife to sew without trimming. Follow the manual’s setup instructions for that technique.
Where can I see the features and package details?
Read Elna’s 792D brochure. An instruction book is included with the machine.
Choose the finish for your next project
Check the current price and availability, or contact our friendly team for help choosing your overlocker and optional attachments.
| Number of Threads | 4 Threads |
|---|---|
| Overlocking Stitch | 4 & 3 Thread |
| Rolled Hem | 3 Thread Rolled Hem |
| Adjustable Stitch Length | 1.00mm to 4.00mm |
| Adjustable Stitch Width | 3.1mm to 7.3mm |
| Differential Feed Ratio | 0.5 to 2.25 |
| Adjustable Foot Pressure | Screw Adjustment |
| Type of Tension | Pull In (Knob) |
| Sewing Speed | Up to 1300SPM |
| Needle System | 15x1SP / HAx1SP (Ballpoint) |
| Machine Cover | Optional |
| Instruction Manual | Included |
| Instructional DVD | Optional |
| Waste Tray | Optional |
Based on 0 reviews
Only logged in customers who have purchased this product may leave a review.
There are no reviews yet.